Auteur Sujet: IC-756 Pro III - La vrai histoire !  (Lu 4001 fois)

Hors ligne VE2EBK Dany

  • Membre junior
  • **
  • Messages: 40
IC-756 Pro III - La vrai histoire !
« le: 20 Novembre 2014, 11:34:52 »
Cette note s'adresse à ceux qui possèdent un ICOM IC-756 Pro III et qui voudront, un jour, le vendre et à ceux, qui un jour,  penseront à s'acheter IC-756 Pro III.

L'article est en anglais mais elle explique très bien pourquoi ICOM a changé le design du PA à la fin 2007 de transistors pour des MOSFET.

Donc, avant de croire à tout ce qui se dire un peu partout, lisez l'article. Si vous avez de la difficulté à comprendre, demander à un amateur  de confiance de vous traduire le texte.
 
Beaucoup d'autres détails techniques sur le IC-756 Pro III sont aussi disponibles sur cette page.

http://www.ab4oj.com/icom/ic756pro3/pro3notes.html

Pour tous commentaires ou mise en doute de l'information mentionnée, s.v.p. communiquer directement avec auteur  A7OJ/AB4OJ    farson@shaw.ca


Note: La vérification n'a pas été fait par moi mais par un amateur de confiance et autant un grand magasin d'équipement en Ontario   que 2 ateliers de réparation radio (une de l'Estrie et une autre de la Rive-Sud de Montréal) peuvent réparer en tout temps les 2 versions de IC-756 Pro III.



Notes on the New IC-756Pro3 MOSFET PA Unit (December 2007)

Mitsubishi, the manufacturer of the 2SC5125 used in the 756Pro series PA Unit, have recently discontinued all their RF power BJT lines. This event has forced Icom to design a new PA Unit based on MOSFETs. To the best of my knowledge, the new PA is showing up in US/Canada Pro3's (#32 variant)  with S/N 32045XX and higher. The MOSFETs are also Mitsubishi parts.

The original PA Unit uses BJT's, not FET's (2SC1971 pre-driver, 2 X 2SC1972 driver, 2 X 2SC5125 PA.) The line-up in the new PA Unit is as follows: 2SC1971 (BJT) pre-driver, 2 X RD15HFV1 (MOSFET) driver, 2 X RD100HHF (MOSFET) PA. The HF/6m PA in the IC-7000 also uses a pair of RD100HHF's.

A typical MOSFET circuit will have 13 dB power gain vs. 10 dB for a BJT circuit. This reduces the required drive power by 50%, i.e. 5W  vs.10W drive for 100W output. This will reduce the driver stage's IMD contribution. The MOSFET PA already has slightly lower IMD (perhaps 1 or 2 dB), so the transmitter will be cleaner overall.

Owners of IC-756Pro3's with the earlier PA Unit need not be overly concerned. The 2SC5125 is a very tough device, and should last for many years with reasonable care. The Toshiba 2SC2782 is a sub for the 2SC5125, and is available from RF Parts singly and in matched pairs. Furthermore, I am confident that Icom laid on an adequate stock of BJT parts at their service centres to maintain the existing installed base when Mitsubishi advised them of the impending discontinuance.

It should be noted that the IC-706 MkIIG went through a similar exercise a few years ago when Motorola discontinued the PA devices.


Note: Rumours that Icom redesigned the PA Unit in response to "PA failures" or "low output" are patently untrue.