Auteur Sujet: Apache Labs - ANAN-10, 100(D) et 200D - SDR HF Transceiver  (Lu 12856 fois)

Hors ligne VE2UGO Hugo

  • Membre guru
  • *****
  • Messages: 871
  • Rapid Deployment Amateur Radio
    • http://files.qrz.com/m/kd4sm/life.jpg
Apache Labs - ANAN-10, 100(D) et 200D - SDR HF Transceiver
« le: 21 Décembre 2012, 15:06:48 »
Apache Labs ANAN-10

https://apache-labs.com/

$1679.00 USD - https://apache-labs.com/al-products/1030/ANAN-10-Transceiver.html


Specifications & Highlights:

Continuous, uninterrupted, receive coverage from 10KHz to 55MHz. .
 
Supports Real-Time display of entire sectrum from 0-55mHz (with suitable PC software)
 
Supports 7 fully independent receivers (sharing the same antenna - and with suitable PC software)
 
Each receiver can display 48/96/192kHz of spectrum
 
Blocking Dynamic Range (ARRL Method) no detectable gain compression
below ADC overload
 
Transmit and receiver image rejection > 110dB
 
Full duplex operation, any split over entire 160m to 6m range.
 
Transmitter two-tone 3rd order IMD of -50dBc on 20m @ 400mW output
 
500mW RF output on 160 – 10m amateur bands, 350mW on 6m
 
Built-in high performance preamp, with a noise floor typically -135dBm in 500Hz
 
Software-selectable 31dB input attenuator in 1dB steps
 
High performance receiver – same specifications as the HPSDR Mercury receiver (ie Dynamic Range typically 125dB)
 
FPGA code can be updated via the Industry Standard TCP/IP network Ethernet connection
 
Seven user-configurable open-collector outputs, independently selectable per band and Tx/Rx (for relay control, etc - with sequencing via PC code)
 
Separate open-collector PTT connection for amplifier control, etc, with sequencer
 
Microphone PTT jumper-selectable from tip or ring connection
 
Bias for electret microphones via jumper
 
Four user-configurable 12 bit analogue inputs (for ALC, SWR etc)
 
Three user-configurable digital inputs (for linear amplifier over temperature, etc)
 
Can operate from a 13.8v DC supply or 12v and 5v supplies
 
Jumper selected in-built low noise and high efficiency switch mode power supply designed by Kjell Karson,LA2NI – less than 600mA (receive - one receiver) from a 13.8V supply
 
I2C bus connector for control of external equipment
 
Full QSK operation (performance dependant on associated PC and control software)
 
Low-level transmitter output for transverter use via user-selectable output attenuator
 
Stereo audio outputs at line and headphone levels
 
In-built 1W stereo audio amplifier for directly driving speakers
 
Direct, de-bounced connections for a Morse key (straight or iambic) and PTT
 
Low phase noise (-137dBc/Hz @ 1kHz) 122.88MHz master clock, which can be phase-locked to an internal 10MHz TCXO or external fequency reference
 
Low phase noise (-140dBc/Hz @ 1kHz at 14MHz) 122.88MHz master clock,
which can be phase-locked to an internal 10MHz TCXO or external frequency
reference
 
Direct ribbon cable interface to Apollo 15W power amplifier, low pass filters and automatic ATU
 
Industry Standard TCP/IP network Ethernet interface supports static, APIPA or DHCP IP address
 
Hermes responds to ping and ARP requests and auto senses network connection speed
 
Eight (8) Layer PCB design for the most professional, state-of-the-art, design available.

==========================================================
Apache Labs adds the following features with the ANAN-10
==========================================================
 
Custom build rugged Extruded Housing for Hermes and the PA
(note: no ventilation holes required in .mil style designs)
 
Mosfet 10W Linear amplifier (160M-6M) gives 15-20W out on HF and 10-15W on 6M
 
LPFs for the PA harmonic suppression and receiver filtering
 
Software Configurable Triple antenna ports
 
SWR Bridge, enables Forward and Reverse Power plus SWR to be displayed using suitable PC software.
 
T/R, LPF Switching using mechanical relays (gold plated contacts)
 
Reverse Polarity protection with resettable fuse
 
All cables, Hardware and instructions to make a complete transceiver with Hermes

« Modifié: 02 Novembre 2016, 13:25:40 par VE2UGO Hugo »

Hors ligne VE2UGO Hugo

  • Membre guru
  • *****
  • Messages: 871
  • Rapid Deployment Amateur Radio
    • http://files.qrz.com/m/kd4sm/life.jpg
Apache Labs ANAN 100D - SDR HF Transceiver
« Réponse #1 le: 02 Mai 2014, 19:14:50 »
Apache Labs ANAN 100D

$3489.00 - Testé dans Practical Wireless UK Mars 2014

"The ANAN 100D is an impressive hardware package that represents the state of the art in SDR hardware design. Not only is the performance excellent but its versatility is exceptional and the facility to upload new FPGA code provides a degree of future-proofing and allows the rig to be easily customised and extended."  Mike Richards, Practical Wireless UK.

https://apache-labs.com/

The Heart of the ANAN-100D is the Angelia SDR:

ANGELIA is a state-of-the-art soft core uP 4th generation DDC/DUC, Hermes-like, transceiver
board that incorporates an Altera Cyclone IV FPGA and dual LTC2208 ADCs. The large FPGA and
dual ADCs permit exceptional versatility and performance. The FPGA is large enough to allow
on-board, soft-core processing, if desired, and the dual ADCs allow true coherent receiver
operations.

Highlights:

100W RD100HHF1 Based 160M - 6M rugged Linear amplifier
Rugged Extruded aluminium housing, Weight: 4.5Kgs approx, Dimensions: 265.5mm (W) x 220mm (D) x 80mm (H)
Combination of 7 LPF and 5 HPF Banks for front end Filtering (User Configurable as well)
6M  LNA
Dual Phase Synchronous LTC2208 16 Bit ADCs
Large 115K (EP4CE115) Cyclone IV FPGA
Supports 7 High performance Independent Receivers on a single ADC
Supports 2 Coherent Receivers using independent ADCs/antennas for beam forming/diversity
FPGA has enough space to add on multiple soft core processors for standalone operation
Onboard 128MB Flash
Onboard 32Mbit Synchronous RAM





« Modifié: 19 Mai 2014, 09:51:10 par VE2UGO Hugo »

Hors ligne VE2PID Pierre

  • Membre guru
  • *****
  • Messages: 4 361
  • Elecraft K2/100/5170 KX1/442 KX2/1464 KX3/190
Re : Apache Labs ANAN-10 - SDR HF Transceiver
« Réponse #2 le: 05 Octobre 2015, 08:12:52 »
...
Publication de la version OpenSDR v 3.2.28 qui 'gère' les SDR de Apache Labs. Cette nouvelle version contient des ajouts pour les fonctionnalités reliées à la Radio Astronomie en plus d'un nouveau Spectral Noise Blanking qui est en sus des NB et NB2 existants.

D'autres ajouts, téléchargements et plus de détails les concernant via http://openhpsdr.org/download.php .

Hors ligne VE2UGO Hugo

  • Membre guru
  • *****
  • Messages: 871
  • Rapid Deployment Amateur Radio
    • http://files.qrz.com/m/kd4sm/life.jpg
Apache Labs ANAN-200D - SDR HF Transceiver
« Réponse #3 le: 02 Novembre 2016, 13:04:06 »
Apache Labs Anan 200D

Sherwood vient d'évaluer le 200D, indiqué en date du 31 août 2016, mais testé en décembre 2015.

http://www.sherweng.com/table.html

Il se classe 9e dans sa liste... Pas si mauvais! Par contre, nous constatons que la ''vieille'' version du K3 était déjà très en avance sur son temps point de vu qualité du récepteur...



Concernant le 100D, il serait 20e en date du mois de novembre 2016 selon les tests de QST.

QST

« Modifié: 02 Novembre 2016, 13:52:29 par VE2UGO Hugo »