Puces et Forums - Radioamateur.ca

Les forums de Radioamateur.ca => Les revues d'équipements radioamateurs => Discussion démarrée par: VE2UGO Hugo le 04 Avril 2014, 17:32:01

Titre: Elecraft PX3 Panadapter
Posté par: VE2UGO Hugo le 04 Avril 2014, 17:32:01
Elecraft PX3 Panadapter pour KX3

 High-performance companion panadapter for the Elecraft KX3 transceiver
 Full-color waterfall and spectrum displays, with fast sweep and excellent sensitivity
 Simple plug-and-play operation—no PC, soundcard, software drivers or setup required
 Weighs just 13 oz (0.37 kg); enclosure size: 5.4 x 3.4 x 1.7” (13.7 x 8.6 x 4.3 cm)


Portable, High-Performance Panadapter PX3

Our new PX3 Panadapter adds a visual dimension to signal hunting, with fast, real-time spectrum and waterfall displays of band activity. Its small size and weight make it ideal for travel or field use.

The PX3 is fully integrated with the Elecraft KX3, utilizing its serial control port and RX I/Q signals*. The panadapter tracks the KX3’s VFO frequency and filter settings via on-screen cursors. You can point and click on signals by rotating and tapping the PX3’s SELECT knob.

With its very wide dynamic range and frequency span of up to 200 kHz, the PX3 offers better performance than most PC sound cards. It’s also one of the most sensitive panadapters available, detecting signals down to the noise floor of the KX3. A PC or Mac can still be connected to the KX3 (via the PX3) for use with logging and control programs.

 
Advanced Features and Signal Processing

PX3 features include multi-pass signal averaging to pull out weak signals, peak detection to show total activity on the band, adjustable reference level, and amplitude range scaling. There’s also a full set of programmable switches to access often-used settings.

The PX3 has a wide supply voltage range (8-15 V) and low current drain (typ. 140 mA @ 13.8 V). It includes a comprehensive manual, and is available factory assembled or as a modular, no-soldering kit.

Planned future features include:
 CW/RTTY/PSK text display
 Use of the built-in USB port with a keyboard or flash drive
 SVGA monitor output option

* The PX3 uses the KX3’s baseband RX I/Q signals. It is not compatible with the 8.2-MHz I.F. signal from the K3.

Buy Here
http://www.elecraft.com/elecraft_prod_list.htm#px3

PX3-K    Panadapter for KX3     499.95
PX3-F    Panadapter for KX3     569.95

Shipping in June according to the latest messages.

PX3 Datasheet: http://www.elecraft.com/manual/PX3%20Data%20Sheet%20rev%20B1a.pdf

(http://4.bp.blogspot.com/-UKMrAauXHV8/U0IF8feVkxI/AAAAAAAAAo4/fWkY8Gmmx50/s1600/IMG_5875262901892.jpeg)

(https://pbs.twimg.com/media/BkZjdH5CAAEjdJp.jpg:large)

(http://img11.hostingpics.net/pics/892547KX3PX3.png) (http://www.hostingpics.net/viewer.php?id=892547KX3PX3.png)

(https://lh6.googleusercontent.com/-kNpwjRjk6xY/U0J9LI_Lz_I/AAAAAAAAVN8/csIymAPXXUQ/s720/P2190169.JPG)

(http://www.elecraft.com/PX3/px3_large.jpg)
Titre: Re : Elecraft Panadapter PX3
Posté par: VE2OK Jean le 05 Avril 2014, 11:55:44
Dans le dernier QST (avril 2014), il y a un article écrit par AA6E, Martin Ewing, sur la construction d'un Tiny Python Panadapter pour le KX3 à coût moindre!

Voici l'article:
http://www.arrl.org/files/file/QST/This%20Month%20in%20QST/April%202014/Ewing.pdf (http://www.arrl.org/files/file/QST/This%20Month%20in%20QST/April%202014/Ewing.pdf)

Voici le site de l'auteur:
http://www.aa6e.net/ (http://www.aa6e.net/)
Titre: Re : Elecraft PX3 Panadapter
Posté par: VE2UGO Hugo le 06 Avril 2014, 01:40:01
D'autres précisions commencent à filtrer!

Apr 4 9:58 PM

A PC can work well, assuming it's fitted with a high-performance sound card, and that you're careful with cables and system grounding. This is sometimes hard to do, especially in a portable situation.

But the PX3 has a true 200-kHz span, and in most cases it will out-perform sound cards in terms of dynamic range. The PX3 also has very low noise thanks to an optimal choice of A-to-D converter (most of them have in-band noise humps that come up above the noise floor). It also has special input circuitry that rejects common-mode noise between the RX I/Q jacks on the radio and the PX3, without the need for isolation transformers.

Beyond that, there are some operators who prefer to have the spectral display right there where the action is, next to the radio. Turning on the PC can then be optional. The PC can still be used with the PX3 since we provide a way to daisy-chain both the control port (ACC1) and RX I/Q signals.

73,
Wayne
N6KR
Titre: Re : Elecraft PX3 Panadapter
Posté par: VE2UGO Hugo le 18 Mai 2014, 21:42:55
Shipping Status (May 6, 2014)

Now taking orders

First shipments will start at the end of June. New orders placed now will ship early August.

http://www.elecraft.com/elecraft_shipping_status.htm
Titre: Re : Elecraft PX3 Panadapter
Posté par: VE2UGO Hugo le 01 Juin 2014, 17:45:47
Wayne a publié une photo montrant le câblage entre le KX3, le PX3 et le KXPA100.

(http://img15.hostingpics.net/pics/414773KXLinecabling.jpg) (http://www.hostingpics.net/viewer.php?id=414773KXLinecabling.jpg)
Titre: Re : Elecraft PX3 Panadapter
Posté par: VE2UGO Hugo le 02 Juin 2014, 12:05:28
Jean-François, VA2SS, vient de publier une petite vidéo du PX3 lors de sa visite au Hamvention à Dayton 2014.

http://youtu.be/NU3Q0wwQu1g

Bon visionnement!
Titre: Re : Elecraft PX3 Panadapter
Posté par: VE2UGO Hugo le 04 Juin 2014, 00:08:41
Une autre vidéo montrant, entre autres, le PX3 en action à Dayton 2014!

http://youtu.be/LnMrQ7YbHpw
Titre: Re : Re : Elecraft PX3 Panadapter
Posté par: VE2UGO Hugo le 20 Juin 2014, 13:25:49
Shipping Status (May 6, 2014)

Now taking orders

First shipments will start at the end of June. New orders placed now will ship early August.

http://www.elecraft.com/elecraft_shipping_status.htm

En date du 20 juin, prolongation de l'attente pour ceux ayant commandé le PX3!

Now taking orders

First shipments will start at the end of July. New orders placed now will ship late August.



Une nouvelle page juste pour le PX3: http://www.elecraft.com/PX3/px3.htm
Titre: Re : Re : Re : Elecraft PX3 Panadapter
Posté par: VE2UGO Hugo le 17 Juillet 2014, 05:49:04
Shipping Status (May 6, 2014)

Now taking orders

First shipments will start at the end of June. New orders placed now will ship early August.

http://www.elecraft.com/elecraft_shipping_status.htm

En date du 20 juin, prolongation de l'attente pour ceux ayant commandé le PX3!

Now taking orders

First shipments will start at the end of July. New orders placed now will ship late August.



Une nouvelle page juste pour le PX3: http://www.elecraft.com/PX3/px3.htm

Nouvelle précision!
First shipments will start at the end of July to early August. New orders placed now will ship late August.
Titre: Re : Elecraft PX3 Panadapter
Posté par: VE2UGO Hugo le 19 Juillet 2014, 06:02:15
Elecraft PX3 Panadapter pour KX3
Buy Here
http://www.elecraft.com/elecraft_prod_list.htm#px3

PX3-K    Panadapter for KX3     499.95
PX3-F    Panadapter for KX3     569.95

Mise à jour des prix!

http://www.elecraft.com/elecraft_prod_list.htm#px3

PX3-K    Panadapter for KX3           499.95
PX3-F    Panadapter for KX3           579.95
          
PWR12V1A-US    Power Supply for K3/0-Mini, 12 V, 1A, 100-240 V, (US Plug Only)     19.95
(The PX3 comes with a pigtail power cable standard. If desired, purchase the optional Power Supply module.)   

(http://stationproject.files.wordpress.com/2014/06/elecraft-pan-adapter-for-kx3.jpg?w=545&h=408)
Titre: Re : Elecraft PX3 Panadapter
Posté par: VE2UGO Hugo le 07 Août 2014, 14:16:43
Shipping Status (August 5, 2014)

Now taking orders

Field Tester PX3s are shipping now (early Aug.), with production shipments starting mid-August.

New orders placed in early August will ship in Sept.
Titre: Re : Elecraft PX3 Panadapter
Posté par: VE2UGO Hugo le 26 Août 2014, 05:46:57
Page officielle du PX3: http://www.elecraft.com/PX3/px3.htm

PX3 Panadapter FAQ: http://www.elecraft.com/manual/PX3_basics_FAQ%20rev%20E.htm

PX3 Installation FAQ: http://www.elecraft.com/manual/PX3_installation_FAQ.pdf

(http://www.elecraft.com/PX3/px3_small.jpg)
Titre: Re : Re : Elecraft PX3 Panadapter
Posté par: VE2UGO Hugo le 05 Septembre 2014, 11:17:25
Shipping Status (August 5, 2014)

Now taking orders

Field Tester PX3s are shipping now (early Aug.), with production shipments starting mid-August.

New orders placed in early August will ship in Sept.

Mise à jour
Shipping Status (August 27, 2014)


Now taking orders

We anticipate shipping the first PX3s late this week or early next week (9/2 - 9/5)

We apologize for the 2 week slip in schedule. We discovered several f/w issues during final testing that needed correction. We are now testing the new PX3 release f/w.

New orders placed in late August will ship in late Sept. to early Oct.[/i]
Titre: Re : Elecraft PX3 Panadapter
Posté par: VE2UGO Hugo le 05 Septembre 2014, 11:33:58
PX3 Owners Manual  Rev A (Aug 25, 2014)
PX3 Owner's Manual (http://www.elecraft.com/manual/PX3_Manual_E740229_REVA.pdf)

PX3 Owner's Manual Errata Rev A-4  (Sep 4,  2014)
PX3 Owners Manual Errata (http://www.elecraft.com/manual/PX3%20Owners%20Manual%20Errata%20A-4.pdf)

Une mention indique que vous devez utiliser le nouveau firmware 2.19, qui est encore en version beta soit dit en passant!

KX3 FIRMWARE VERSION 2.19 REQUIRED
Your KX3 must be equipped with firmware version 2.19 (or later) or your PX3 will not operate properly. The latest KX3 firmware is available on the Elecraft web site. If you haven’t updated your KX3 firmware before, see FIRMWARE UPGRADES in your KX3 Owner’s manual for instructions. If you have already connected your PX3 to your KX3, you can update the KX3 firmware without disconnecting them as described under Updating KX3 Firmware on page 23 of this manual.


KX3 Beta Firmware Revision
MCU 2.19 / DSP 1.30, 9-04-2014[/b][/i]
ftp://ftp.elecraft.com/KX3/firmware/beta/kx3fw2r19.zip

 New Features:

PX3 SUPPORT: On a band change, the first command sent by the KX3 to the PX3 is “BN” (band number) to ensure correct handling of subsequent commands.
(...)

* 8 septembre 2014 Maintenant en version officielle: http://www.elecraft.com/KX3/KX3_software.htm
Titre: Re : Elecraft PX3 Panadapter
Posté par: VE2UGO Hugo le 12 Septembre 2014, 19:20:38
PX3s have started shipping

PX3-F orders started shipping this week. We are currently shipping PX3-F domestic orders from 4/4/14.

We will be slowly ramping up over the next few weeks. Prior to shipping you will receive an email to confirm your order. PX3-K and international orders will begin shipping within the next 2-3 weeks.

New orders placed now will ship in mid-late October.

We appreciate your patience and ask that you not contact sales or support to find out your place in line. This slows down are processing and we want to get these out as quickly as possible.

We are unable to give you an exact place or shipping date at this time.
Order dates will be updated on the status page as we email. Remember the early days have the most orders per day and will take longer to get through.


PS:
Elecraft Year End inventory Sept. 11-15.

During this time we will not be able to ship orders. Our last day of shipping will be Wednesday, Sept. 10 and we will resume shipping
Tuesday Sept. 16th. We will make every effort to ship all orders placed prior to Sept. 10 before inventory.
Titre: Re : Elecraft PX3 Panadapter
Posté par: VE2UGO Hugo le 17 Septembre 2014, 17:43:06
Pour les détenteurs du PX3! Est-ce qu'il a déjà des propriétaires au Québec du PX3?

PX3 Beta Firmware Revision
MCU 90.36 , 9-15-2014


http://www.elecraft.com/PX3/PX3_software.htm

PX3 rev. 90.36 firmware was intended as an internal-only Elecraft test release--this explains the odd numbering ("90.36"). You can still treat it like any other beta release, by placing the .hex file into a folder and using PX3 Utility's browsing capability to get to it. However, once we have a new release (1.08), hopefully later in the week of Sept. 15th, you'll need to delete the 90.36 hex file. Otherwise PX3 Utility will not be able to find rev. 1.08.

- Disabled experimental "REF_COMP" feature (not ready for use).
- SPAN Autoscale defaults to OFF after a CONFIG reset. See manual for details on this feature.
- REF level is now recalled correctly, per band, including on power-up.
- Fixed Stepped Span (menu entry); see manual for details.
- Improved front panel switch tap/hold timing.
- Fixed bug in which some of the X-axis tics along top edge had visual artifacts as SPAN was changed.
- Fixed bug in which MKR A and B were not resetting consistently on band change.
- Added #NB and #NBL remote control commands. #CAL command also now works for both GET and SET.
Titre: Re : Elecraft PX3 Panadapter
Posté par: VE2UGO Hugo le 17 Septembre 2014, 17:48:22
Shipping Status (September 17, 2014)

PX3-F:
Confirming emails have been sent to customers who have ordered the PX3-F Factory Assembled Panadaptor between April 4 and April 15.

If you ordered a PX3-F only during that time and have not received an email please email sales@elecraft.com and let us know.

PX3-K:
We will start emailing customers who ordered PX3-K Kits within the next 3-5 days to confirm orders for shipping.

Watch for your email and be sure to reply right away.
You can leave the following section on the status page.

New orders placed now will ship in mid-late October. We appreciate your patience and ask that you not contact sales or support to find out your place in line. This slows down our processing and we want to get these out as quickly as possible.

We are unable to give you an exact place or shipping date at this time.
Order dates will be updated on the status page as we email. Remember the early days have the most orders per day and will take longer to get through.
Titre: Re : Elecraft PX3 Panadapter
Posté par: VE2UGO Hugo le 19 Septembre 2014, 19:46:27
PX3 Beta Firmware Revision
MCU 1.09 , 9-19-2014

 
- Rev. 1.09 of the PX3 requires KX3 firmware version 2.21 or later
- Stepped span feature added.
- Fixed bug that caused a connected KXPA100 to turn off and/or PX3 to lock-up.
- Removed REF COMP mode.
- Span Autoscale now defaults to OFF after a configuration reset.
- Fixed pixel artifacts at top of screen and narrow tick marks when tuning VFO.
- Fixed bug that cause the MKRA and/or MKRB to not reset on a band change.
- Serial command #CAL added. #CAL1 turns on calibrator, #CAL0 turns it off.
- Fixed bug in which Ref Lvl was not getting saved per band.


http://www.elecraft.com/PX3/PX3_software.htm
 
Titre: Re : Elecraft PX3 Panadapter
Posté par: VE2OK Jean le 25 Septembre 2014, 07:19:27
Dear Elecraft Customer,

Your PX3-K order will be available to ship in the next 3-5 business days.

Attached is a copy of your order.

Please confirm via return email that all the information is correct, including your shipping/billing address and invoiced products.

We cannot ship your order without confirmation so please respond via email as soon as possible.

For credit card updates, you may submit new credit card information at the following link: http://www.elecraft.com/newcc.html

If you need the shipping delayed for any reason that is fine. We can ship at a later date but we cannot hold orders.

Payments already received will be applied to your invoice. Credit cards will be charged the day before or day of shipment.

Once we have received your confirmation, your order will ship as soon as possible, allow 3-5 days.


We look forward to your reply.

Best Regards,
Lisa Jones
Elecraft Sales
831-763-4211
lisa@elecraft.com
Titre: Re : Elecraft PX3 Panadapter
Posté par: VE2PID Pierre le 02 Octobre 2014, 22:06:02
.. ..
Gems Products qui offre des côtés et un couvercle protecteur pour le KX3 revient cette-fois avec l'équivalent pour le PX3.
Cliquer ici Panneaux/couvercle PX3. (http://gemsproducts.com/PX3.html)
Titre: Re : Elecraft PX3 Panadapter
Posté par: VE2UGO Hugo le 02 Octobre 2014, 22:16:08
Gems Products avait annoncé, avant sa sortie, qu'il avait une version pour le PX3... Par contre, il est le même prix que pour le KX3 qui est plus gros...

De plus, il a aussi une ''protection'' pour le troue du Keyer quand non utilisé également!
http://gemsproducts.com/Images/KX3%20Pix/KXPD%20Cover%201.jpg

Un nouveau système de montage va également être produit très bientôt pour le KX3. Surement un similaire à celui annoncé au départ par Elecraft et qui ne sera jamais produit semble t-il...
Titre: Re : Elecraft PX3 Panadapter
Posté par: VE2OK Jean le 11 Octobre 2014, 22:52:38
J'ai finalement reçu mon PX3 et j'ai pu le monter avec 3 temps libres de 10 minutes!. C'est un vrai kit pour mécano, très simple. Ça ne vaut pas la peine de payer 80$ US pour l'avoir déjà monté. Les premiers essais sont très intéressants, ça permet d'obtenir une plus grande précision dans la recherche de signaux faible et d'être directement sur le signal. À suivre...
Titre: Re : Elecraft PX3 Panadapter
Posté par: VA2SS Jean-François le 12 Octobre 2014, 09:09:22
Bien content pour toi!

Je suis bien d'accord avec toi également pour l'assemblage, c'est simple et l'expérience est très intéressante.

Surveille bien la sortie prochaine en version beta d'un nouveau firmware qui règle quelques problèmes d'affichage des modes digitaux avec le px3.

Merveilleux pour travailler en split lors d'un DX  ;D

Tient nous au courant !!

73
Titre: Re : Elecraft PX3 Panadapter
Posté par: VE2OK Jean le 12 Octobre 2014, 18:06:08
J'adore ce nouveau produit qui rend encore plus précis le KX3. De plus, rendre visuel le son, c'est fantastique pour un visuel.

Sur le côté gauche, il y a une sortie USB identifiée Keybd qui ne sert pas actuellement et pour usage futur. Savez-vous quels sont les intentions d'Elecraft concernant ce port USB?
Titre: Re : Elecraft PX3 Panadapter
Posté par: VA2SS Jean-François le 12 Octobre 2014, 18:07:35
Une bonne nouvelle Jean....

«We plan to add a USB keyboard interface later this year.»

Wayne
 N6KR


73
Titre: Re : Elecraft PX3 Panadapter
Posté par: VE2OK Jean le 13 Octobre 2014, 20:25:05
Mais encore, pour faire quoi?

Ce que je souhaiterais, c'est une connection USB avec l'ordinateur pour être capable d'utiliser le KX3 à distance avec un ordinateur portable.
Un peu comme le K3-remote mais sans toute la quincaillerie, uniquement logiciel. Par exemple prendre le café le matin sur la terrasse et profiter du KX3 à distance sans aucun fils d'antenne.
Titre: Re : Elecraft PX3 Panadapter
Posté par: VE2UGO Hugo le 13 Octobre 2014, 20:43:12
Bonsoir Jean,

L'objectif premier du USB sur le PX3 est de connecter un clavier afin de faciliter les communications en numérique avec le KX3. Pas besoin d'ordinateur. Seulement le KX3 avec le PX3 et un clavier USB.

Plus tard, il y aura aussi une fonction pour y connecter un écran externe!

Voili voilou!
Titre: Re : Re : Elecraft PX3 Panadapter
Posté par: VA2SS Jean-François le 13 Octobre 2014, 21:30:43
Bonsoir Jean,

En fait, c'est possible depuis un bout de temps. Avec le logiciel Win4K3, la version pour le KX3, et en plus développé par un amateur québécois, tu pourrais prendre le contrôle de ton KX3 à distance. Ça de prend un ordinateur relié au KX3, le logiciel Win4K3 (version KX3)et un logiciel de redirection de port via TCP/IP comme VSPE d'Eterlogic. Et pour le transport de l'audio, il existe plusieurs possibilité, comme en autre l'utilisation d'un compte dédié Skype. Personnellement, je ne trippe sur cet choix.

http://va2fsq.com/?page_id=683 (http://va2fsq.com/?page_id=683)

(http://va2fsq.com/wp-content/uploads/KX3ScreenHR.jpg)

Cependant, avec Win4K3 et Splashtop.... (à expérimenter)... Pour la connexion distante, une simple tablette Windows 8 pourrait faire l'affaire. Quelques 'un l'on expérimenté dernièrement et ont obtenu bien du succès.

http://www.splashtop.com/personal (http://www.splashtop.com/personal)

https://www.youtube.com/watch?v=LH0jrTtOjU8 (https://www.youtube.com/watch?v=LH0jrTtOjU8)

Et pour les plus «trippeux» et plus fortuné, avec un 2e KX3, tu pourrais contrôler le 1er, un peu comme pour le K3/0. Un petit paragraphe qui est sûrement passé inaperçu dans le manuel du KX3...

Using the KX3 as a Remote Front Panel You can use the KX3 as a front panel for a remotely located KX3 or K3. (At present this feature is experimental, providing limited control capabilities.) The two transceivers can be tied together via the internet or wiFi using adapters at each end that handle data and audio. An alternative is to tie the transceivers together directly via the serial port (ACC1), using a “null-modem” cable (a cable with the tip and ring connections swapped from one end to the other).  To enable the remote-control function at the “local” KX3, which acts as a front panel only, set MENU:AUTO INF (auto-info) to RIG CTRL. 


Pour le PX3, seul des améliorations et des ajouts de nouveautés par une mise à jour du firmware est prévu en ce moment. Même si le site d'Elecraft annonce toujours «SVGA monitor output option» sur son site web, il a malheureusement été repoussé dans les cartons pour le moment. À suivre.

L'ajout du support du clavier via la prise USB du PX3 pour les modes numériques autonomes (sans PC) en cours de test en ce moment. La sortie d'un nouveau firmware n'est pas «iminente», mais disons pour le moment que le développement avance bien.

Bonne expérimentation Jean !

Ce que je souhaiterais, c'est une connection USB avec l'ordinateur pour être capable d'utiliser le KX3 à distance avec un ordinateur portable.
Un peu comme le K3-remote mais sans toute la quincaillerie, uniquement logiciel.
Titre: Re : Re : Elecraft PX3 Panadapter
Posté par: VA2SS Jean-François le 13 Octobre 2014, 21:44:21
J'ai finalement reçu mon PX3

En passant, je t'invite à mettre à jour ton KX3 à la version beta 2.25 et ton PX3 à la version beta 1.12 qui vient finalement de sortir. Je l'ai en test depuis 1 semaine et ça corrige, en autre, le bug d'affichage du filtre DSP à l'écran du PX3 lors de l'utilisation des modes digitaux.

73
Titre: Re : Elecraft PX3 Panadapter
Posté par: VE2OK Jean le 13 Octobre 2014, 22:58:37
C'est déjà fait!

Intéressant le Win4K3 et le Splashtop. Je vais commencer par expérimenter le Splashtop pour voir si ça fonctionne bien car sinon, je n'ai pas d'intérêt d'installer seulement le Win4K3.
Titre: Re : Elecraft PX3 Panadapter
Posté par: VE2OK Jean le 19 Octobre 2014, 22:54:57
Bon voici mes premiers essais. Pour le Splashtop, c'est simple et c'est facile de prendre à distance sur mon Android un des deux ordinateurs branchés sur Splashtop. Le son fonctionne aussi.

J'ai installé le Win4K3 avec mon KX3 sur un portable Lenovo X-61 (WIN 7, 64 bits)  relié par le câble KXUSB d’Elecraft. Tout fonctionne sauf le son de l’ordinateur. J'ai branché un cable de son sur la sortie du KX3 et à l'entrée de l'ordinateur. J'ai finalement entendu le son à la sortie de l'ordi mais c'est là que ça se complique lorsque je me branche à Splashtop, le son ne fonctionne pas sur mon Android (petit détail car sans son, ça ne sert à rien).

J’ai essayé la même chose sur mon ordinateur de base (WIN 7, 64 bits) et le même problème est apparu.

J’ai parcouru toute la documentation et je n’ai rien encore trouvé?

J'ai écrit à VA2FSQ (TOM) et voici sa réponse.

Bonjour,
Le KXUSB fonctionne uniquement avec les commandes de serial port . Il ne passe pas son. Il faut que tu  connecte la sortie audio sur le KX3 à une entrée audio sur votre ordinateur . Aussie, le sortie de son audio sur votre PC  à l'entrée de la ligne ( ou microphone ) sur le KX3 . Ensuite, vous configurez le son sur Splash top
J'utilise Skype et TeamViewer . Fonctionne avec les tablettes Android aussi . C'est gratuite.

S'il vous plaît recherche pour le raccordement d'un son KX3 à votre ordinateur sur Internet . Je n'ai pas de documentation pour ca. Sur Elecraft il y'a la documentation pour le  KX3-PCKT cables.

73's Tom


Je ne comprends pas pourquoi je dois branché la sortie audio de mon ordi à l'entrée de mon micro. Le cable KXUSB devrait faire l'affaire. J'ai également une sortie RX I/Q que je peux relier au PC que je n'ai pas branché. Ai-je besoin d'un interface de type Signalink pour brancher l'ordi au KX3? Je suis un peu mêlé dans tous ces câblages. Besoin d'aide S.V.P.  :-\
Titre: Re : Elecraft PX3 Panadapter
Posté par: VE2UGO Hugo le 15 Décembre 2014, 17:33:32
QRZ utilise la vidéo de Jean-François, VA2SS, sur sa présentation du PX3.

Good job JF! ;)

http://qrznow.com/elecraft-px3-panadapter/
Titre: Re : Elecraft PX3 Panadapter
Posté par: VE2UGO Hugo le 24 Avril 2015, 02:29:25
PX3 Beta Firmware Revision
MCU 1.25 , 4-17-2015

* A new fixed-tuning mode keeps the PX3 display constant as the KX3 is tuned. Associated menu entries are "FixTrack" to toggle between fixed-tune and tracking mode and "FixMode" to select the behavior when the VFO cursor reaches the edge of the display. Operation is similar to the P3.
* The knob interface has been improved for smoother operation.
* The AFSK cursor is now on the correct frequency.
* There is no longer a sudden jump in display resolution when adjusting the span below 5 kHz
.

http://www.elecraft.com/PX3/PX3_software.htm

(http://www.elecraft.com/PX3/px3_small.jpg)
Titre: Re : Elecraft PX3 Panadapter
Posté par: VE2UGO Hugo le 05 Septembre 2015, 19:39:23
"Hi all,

This afternoon I installed an early version of the PX3 firmware with full keyboard support. Works great with a Logitech K360 wireless keyboard (a real steal at $19). I made a few QSOs in both CW and RTTY mode (FSK-D on the KX3) to check things out.

The PX3 won't work with just any USB keyboard. For example, those that include other built-in USB devices such as trackpads will not work with this implementation. So I strongly recommend not purchasing one until we provide a list of those we've tested.

There are a still a few wrinkles to work out, but it is most definitely a nice addition to the PX3. We'll be looking for a few testers when the next version is ready (please wait for the announcement before you volunteer :)

73,
Wayne
N6KR"
Titre: Re : Elecraft PX3 Panadapter
Posté par: VE2UGO Hugo le 06 Septembre 2015, 17:29:46
Voir ici pour une solution clavier/souris pour le PX3: http://www.wickedstone.com/KF5WBO/Mouse-n-ClickQSY.pdf

Vidéo:
http://m.youtube.com/watch?v=Rv6Tmv9Dlwo

http://m.youtube.com/watch?v=D32PbJY60Uk
Titre: Re : Elecraft PX3 Panadapter
Posté par: VE2UGO Hugo le 15 Octobre 2015, 09:39:56
PX3 Beta Firmware Revision
MCU 1.35 , 10-13-2015



* Added USB keyboard support (see PX3_Keyboard_QuickStart.pdf for usage), most keyboards are supported except Bluetooth, Apple and those with mice.
* Added separate font for Text Decode, which can be different than system font.
* Three lines of RX text, 2 lines of TX text.
* Added 7x11 font which was introduced on the P3
* Added serial commands #USB, #BCN,#BCI, #BCL, #TXM, #TXH to support keyboard.
* Added ability CR and LF in text messages ‘\r’ for CR, ‘\n’ for LF
* Fixes wrong direction spectrum when VFO A is tuned on 2 meters.
* Fixes default values for USB keyboard values when upgrading.
* Fixes ‘smearing’ U-shaped VFO A cursor when fixed tune is enabled.
* Fixes bug with some older units that could have prevented USB from operating.
* Fixes Ctrl-Alt-R keyboard replay, removes garbage characters.
* Fixes missing characters entered with key when no keyboard attached.
* Fixes a problem with RefLvl being too high after upgrading firmware.
* Fixes an issue with display freezing when RIT/XIT was adjusted on KX3 Fixes displayed frequency not updating when RIT was turned off.
* Limits waterfall size when text display is active, so menus are displayed correctly.
* OSB amplitude and phase serial commands added.
Titre: Re : Elecraft PX3 Panadapter
Posté par: VE2UGO Hugo le 02 Novembre 2015, 01:23:59
PX3 Beta Firmware Revision
MCU 1.37 , 10-30-2015


Please read PX3 Beta Firmware Instructions for installing beta firmware.
It is highly recommended to read PX3 Keyboard Quickstart.

* Added Ctrl-H help screens to USB keyboard. Help is also available in macro/text message entry.
* Embedding \p in text message will insert contents of replay buffer.
* Use Alt-R to clear replay buffer without clearing text windows.
* Keyboard macros 1-8 may now be set to execute using the PX3 front panel FN keys.
* Prevents creation of blank/empty macros/text messages.
* Fixes red waterfall on 160 and 2 meters after upgrading.
* Fixed missing CW elements with paddles after using keyboard.
* Fixed missing macro/text message 1 display during edit when first powered up.
* Fixed garbled bitmap saves when using PX3 Utility.
Titre: Re : Elecraft PX3 Panadapter
Posté par: VE2UGO Hugo le 08 Novembre 2015, 10:56:02
PX3 Production Firmware Revision
MCU 1.39 , 11-5-2015


* Rev. 1.16 or later of the PX3 requires KX3 firmware version 2.27 or later
* Adds: USB keyboard support. Most PC keyboards are supported except Bluetooth, and those with mice. Please refer to revision A6 of the PX3 Manual (currently available on the Elecraft website) for instructions and examples. The text display window now displays 3 lines of RX text and 2 lines of TX text. Features include 50 message & 50 macro memories, beacon mode, replay buffer, and more.
* Adds: The 7x11 font first introduced on the P3, now available on the PX3.
* Adds: serial commands to support keyboard, #USB, #BCN, #BCI, #BCL, #TXM, and #TXH .
* Adds: serial commands to adjust OSB amplitude/phase values, #OSBP, #OSBA.
* Fixes: ‘smearing’ U-shaped VFO A cursor when fixed tune is enabled.
* Fixes: an issue with display freezing when RIT/XIT was adjusted on KX3
* Fixes: displayed frequency not updating when RIT was turned off.
* Fixes: missing CW elements with paddles after using keyboard.
* Fixes: garbled bitmap saves when using PX3 Utility.
Titre: Re : Elecraft PX3 Panadapter
Posté par: VE2UGO Hugo le 16 Avril 2016, 01:48:34
PX3 Beta Firmware Revision
MCU 1.42 , 3-22-2016

* Adds: keyboard macros can now be executed even when the Text Display is turned off.
* Adds: #RCF command: “Relative Center Frequency” applies an offset to the center frequency based on the passed argument. Usage: #RCFsnnnnnn; Where: ‘s’ is the sign + or -, nnnnnn is the offset in Hz. For example, if the PX3 is set to a 30 kHz span and you would like to position the cursor on the left edge: #RCF+015000; Using #RCF without any arguments returns the difference in Hz between the center frequency and the vfo frequency.
* Fixes/Adds: Removed replay buffer and its controls and in its place added a “scratchpad” to hold temporary text such as call signs, names, etc. Text may be added to the scratch pad by first pressing the Insert key. The scratchpad is cleared each time it is opened. To move the scratchpad contents to the Tx buffer, press Ctrl-Insert. Pressing Ctrl-H when the scratchpad is open, displays a help screen. To exit the scratchpad, press Esc, Enter or Insert. You may also press a text macro assigned key which will execute after exiting the scratchpad. To embed the scratchpad contents in a text message, use \s . The scratchpad holds one line of text. It is erased after each power cycle.
* Fixes: USB/LSB passband inversion when using transverters.
* Fixes: an issue when using the ‘|’ command (IM) with text message strings shorter than 10 characters. The IM character is now correctly interpreted which should solve the problem of truncated strings.
* Fixes: Keyboard help screen being overwritten by spectrum trace and grid.
* Fixes: Full Tx keyboard buffer overflow issue in which buffer could not be sent with Enter.

PX3 Owners Manual Rev A7 (March 9, 2016): http://www.elecraft.com/manual/E740229%20PX3%20Owner's%20Manual%20A7.pdf
Titre: Re : Elecraft PX3 Panadapter
Posté par: VE2UGO Hugo le 24 Février 2017, 00:44:29
PX3 firmware revision 1.48 is now available for download as a general release using the PX3 Utility.  This version is essentially the previous beta 1.45 along with a few minor fixes and one additional feature.  There is a new version of the PX3 Programmer's Reference (rev A6) as well a new errata (A8-1), which are both available from the Elecraft website.

Release notes for this version:

MCU 1.48 / 02/08/2017

Note: refer to the latest PX3 manual and PX3 Programmer's Reference for more information regarding these new features.

* Adds: USB MSD (mass storage device, memory stick, thumb drive) support.  Most types of flash drives are supported.  Added a new sub-menu called “MSD menu” which includes the following features: 
   + Scrn shot – takes a .bmp screen shot of the current screen. 
   + ConfgSave – saves the current configuration.
   + ConfgRstr – restores the configuration.
   + XportMacr – exports macros/text messages to a file which can be edited.
   + ImprtMacr – imports macros/text messages from a file.
   + Set Clock – allows setting of the clock used for file operations.


* Adds: Serial commands #MAA, #MBA to adjust A or B markers by an incrementing or decrementing.  The adjustment value is the same as used by the K3/KX3 UP and DN commands.  Usage: #MAAsn
      s = + to increment, - to decrement
      n = 0 adjust by 1 Hz
      n = 1   “   “  10 Hz
      n = 2   “   “  20 Hz
      n = 3   “   “  50 Hz
      n = 4   “   “  1 kHz
      n = 5   “   “  2 kHz
      n = 6   “   “  3 kHz 
      n = 7   “   “  5 kHz 
      n = 8   “   “  100 Hz
      n = 9   “   “  200 Hz
Or:
   #MAAs
      s = + to increment, - to decrement. The step size is automatically determined by the current span and mode:   
      
USB, LSB, AM & FM
Span < 5 kHz – step = 10 Hz
Span 2-9.99 kHz – step = 20 Hz
Span 10-49.9 kHz – step = 50 Hz
Span 50-99.1 kHz – step = 100 Hz
Span 100-200 kHz – step = 200 Hz
   

CW & Data
Span < 5 kHz – step = 2 Hz
Span 2-9.99 kHz – step = 20 Hz
Span 10-49.9 kHz – step = 50 Hz
Span 50-99.1 kHz – step = 100 Hz
Span 100-200 kHz – step = 200 Hz


* Adds: Frequency displays now show all digits including the Hz digit.  This includes the center frequency adjustment and marker values.  Note that markers adjust by values determined by the current span setting.

* Adds: To enter the text decode scratchpad, you can now use either Insert or Alt-P.  To send the scratchpad, you can now use either Ctrl-Insert or Ctrl-P .

* Adds: #MSS msd screen shot serial command.